Wholesale automatic rubber moulding machine,rubber injection moulding machine price,rubber moulding machine manufacturer,Custom rubber transfer moulding machine,silicone rubber moulding machine

Sonly 438Ton Servo System Energy Saving Horizontal Injection Molding Machine

Name: Wholesale Custom automatic silicone rubber transfer injection moulding machine price manufacturer
Brand: SONLY
Availability: InStock

Inquiry Basket

OEM：

Available

Sample：

Available

Payment：

Other

Place of Origin：

China

Supply Ability：

1000 unit per Month

Product Details

The operator needs to check the power cord for leakage before turning on the switch. In addition, it is also necessary to confirm whether the amount of hydraulic oil is sufficient, and check whether the proximity switch of the safety door is malfunctioning.

Mold installation

1. The mold must be installed manually, use the fixed circle of the fixed plate to close the safety door, and then adjust the equipment to close the mold.

2. When adjusting the mold, make sure that the nozzle is in the center of the gate sleeve, align up and down, left and right, and then fix the mold on the fixed plate.

3. Adjust the stroke and speed of the thimble, and set it as short as possible. If the stroke of the thimble does not meet the relevant regulations, the mold may be damaged.

4. Adjust the die closing safety device.

Manual operation steps of horizontal injection molding machine

1. Switch the operation switch to the "manual" position, and then press the pump start button.

2. Close the safety door, switch the mold switch to the "close mold" position, and start the mold closing action.

3. Switch the injection device to the "forward" position to complete the nozzle contact.

4. Switch the injection device to the "injection" position, and then perform the injection action. The pressure is converted from the injection pressure (ie the primary pressure) to the secondary pressure. Note: In order to avoid screw damage, it is necessary to start the screw drive motor 15 minutes after the heating cylinder reaches the set temperature.

5. Measure the pressure holding time.

6. Switch the screw switch to the "rotation" position to measure.

7. Switch the injection device switch, and the injection device retreats to the proper position.

8. After measuring the cooling time, switch the mold switch to "open mold".

9. Finally press the "Eject" button.

The automatic operation steps of the horizontal injection molding machine

1. Before entering the automatic operation, set the timer and switch the operation selection switch to "semi-automatic".

2. After confirming the safety of the operating environment, close the safety door.

3. Switch from low pressure to high pressure when closing the mold.

4. When the clamping pressure rises, the injection device will move forward, and the injection will start after the nozzle is in contact.

5. When the timer of the injection device reaches the set time, the cooling and material will start to be measured, and the screw will also rotate and retreat.

6. Reduce the pressure in the closed mold cylinder, and then perform the mold opening action.

7. After the mold opening action is stopped, the ejection action is performed. At this time, the finished product is ejected from the ejector pin and falls onto the finished product drop plate.

During the operation of the horizontal injection molding machine, if an emergency stop is required, the "emergency stop" button on the operation panel should be pressed immediately. Finally, turn off the power and clean the machine after the operation to ensure the safety of the equipment.

Main Features：

One.The Lock Section

1.Arch template, effectively protects the mould, especially suitable for big template with small mold.

2.The electric ruler is installed on the crosshead, the position is more precise.

3.The front connecting rod uses connected structure, increases the rod strength, and easy for assembly

4.The connected tail-board stills itself with big lock shaft, improves tail-board strength, and ensures zero abrasion of the tail-board, easy for maintenance.

5.Connected movable plate, improves its rigidity and reduces deformation

6.Connected thrust bearing, improves its strength and stills itself with small lock shaft, ensures zero abrasion.

7.Arch template fully complies with mechanical property, largely improves template strength.

8.More reasonable toggle design, speeds and stabilizes mold opening and closing.

9.Adjustable movable plate mounting plate, makes the installation easier.

10.Mixed design of T-shape groove and die hole, increases universality of the mold.

Two.The Injection Section.

1.Bridge type support, improves injection smoothness.

2.Longer length-diameter ratio screw design, improves plasticizing effect.

3.Double seal structure, ensures no oil leakage.

4.Withhold type press plate, easy for debugging and assembly.

5.Bijection structure, improves stability.